(Why threads strip and bolts break)
When a bolt and nut is tightened to draw the bolt head and nut together it stretches the shank, deforms the threads and loads the object trapped between the bolt head and nut.
The bolt shank acts like a spring being pulled apart and it tries to return to its unloaded condition.
The amount of tension developed in the shank is dependent on the number of turns of the nut.
The size of the torque required to turn the nut has little to do with the tension applied to the bolt shank.
Rather the amount of torque needed to turn the nut reflects the slipperiness of the threads.
Keywords: bolt tension, yield stress, the coefficient of friction.
Intro to nut torque and bolt threads
The nut torque stated in bolt tension tables is based on lubricating threads with light oil.
When another lubricant is used the torque values must be adjusted to get the 65% to 75% yield stress recommended for bolted connections.
The ease with which a nut moves on a bolt thread affects the torque required for it to turn. As the nut tightens down, its threads are squashed against the threads of the bolt shank.
The two threads wedge together against each other.
The turning nut rides down the bolt shank threads, eventually squashing against the clamped surface until the combined thread and nut bearing surface friction resistance prevents further movement.
Considering surface area and the bolt shank
The bearing surface area under the nut and bolt head is larger than the cross-section of the bolt shank.
In the case of metal flanges being clamped together with the nut bears against the flange, the bolt shank begins to lengthen, and the threads in the nut and bolt start to distort.
The threads distort and become loaded one at a time.
As the shank lengthens the strain causes the atomic structure to deform. The atomic structure reacts like a taut spring and a counter force acts to hold the atoms together.
If the nut continues to be tightened the shank lengthens further and the stress rises.
If the stress reaches a sufficient amount known as the yield stress, the atomic ‘spring’ structure deforms permanently. And if the nut is turned further the bolt eventually shears at the area of greatest stress.
If instead, the threads were the weaker part of the bolt assembly, it would be they that distorted to the point of failure and strip.
Bolts are tensioned normally by turning the nut until the effort to turn the nut reaches a certain force.
An alternate method is to heat the bolt to a specific temperature that expands it a given length and then put the bolt into the hole with the nut done up firmly snug and then let the bolt cool down.
Torque-up method
The torque-up method is cheap and quick but poor in accuracy.
The bolt lengthening method is very accurate but time-consuming and costly.
The torque-up method relies on friction between nut and bolt threads to produce the reaction to the tightening torque.
If the friction is low the threads will undergo more loading before the friction force matches the tightening force.
If the threads are rough the friction force is greater and sooner matches the tightening force.
Always lubricate threads
A good practice is to never do up threads dry but to always lightly lubricate them.
The lubricant reduces the effects of the thread surface roughness and lowers the friction between the nut and bolt. It provides a near consistent friction value on all the bolts and improves the accuracy of getting the same bolt load in all the bolts.
It also improves the accuracy of reaching the same bolt load for those bolts used repeatedly.
Rub your hands together and feel the friction they generate.
Now put some liquid detergent and water on them and rub the detergent into your hands.
When you rub them together with the detergent as lubricant there is much less friction and they slide over each other easily.
In other words, the detergent reduces the force required to rub your hands.
The same occurs when a lubricant is put on bolt threads. Less torque is needed to do up the nut.
The more slippery the lubricant, the less torque needed
The table below shows the maximum and minimum coefficients of friction for a range of thread surfaces with lubricants.
As the coefficients of friction drops, less torque is needed to tighten the nut.
With very low friction on small diameter bolts the nut can be turned so easily that the bolt will stretch past its yield before the right nut torque is reached, and the bolt breaks.
| Surface/Lubricant | Friction Coefficient Min | Friction Coefficient Max |
| Bare passivated surface | 0.1 | 0.25 |
| Baked on MoS2 film | 0.04 | 0.1 |
| Molycote G Paste | 0.04 | 0.09 |
| Liquid Teflon (water based) on MoS2 | 0.03 | 0.10 |
For Teflon…
If using Teflon coated threads the recommended nut torque based on oil lubricated threads no longer applies and the torque value must be lowered to prevent the bolt being over- loaded.
Check with the bolt supplier as to the correction factor or do your own bolt stress versus lengthening trials under specific torque loads.
Summary
The total nut turning torque depends on both the thread slipperiness and the slipperiness of the bearing face under the turning fastener component.
The surface area of the nut contacting the flange produces additional friction.
At times it is necessary to turn the bolt because it is not possible to turn the nut.
In this case, the required torque for the bolt turning will not be the same as that for turning the nut.
Mike Sondalini – Equipment Longevity Engineer.
We (Accendo Reliability) published this article with the kind permission of Feed Forward Publishing, a subsidiary of BIN95.com
Web: trade-school.education
E-mail: info@trade-school.education
If you found this interesting you may like the ebook Process Control Essentials.
when torqueing a 18-8 stainless steel bolt into a threaded steel plate 1″ thick would the torque value be the same as torqueing a stainless steel nut ?
Been thinking about this query.
A properly tensioned bolted connection requires the correct bolt shank tension be achieved to make the connection operate properly under its service loads and in it service environment. The strain reached within the microstructures of the fastening components (i.e. shank or stud, nuts, washers) caused by tensioning needs to be the values that lets the connection work properly during its service duty. The torque value needed to produce the shank or stud tension would change in accord with the microstructure properties of the materials, so using an 18-8 stainless steel bolt threaded into steel plate is not the same situation as using an 18-8 stainless steel nut on a steel stud because the shank/stud materials are different.
Contact a bolting engineer and get their advice on the tensions and torques needed when you don’t use industry standard, pre-designed and approved fastening configurations.
All the very best to you,
Mike Sondalini